Hue Switch ConsoleSign in

Open source · For Philips Hue

Build a wall switch for your Hue lights.

Flash a Seeed Studio XIAO from Chrome or Edge, pair it with your Hue Bridge, and choose what each button does. Presses go straight to the Bridge on your home network, and firmware updates arrive over Wi-Fi.

New accounts accept the Terms and the Safety notice before using the console.

Sign-up is by invitation for now. Already invited? Sign in

Read the setup guide →
Round · 3 parts

A touch screen that snaps onto a XIAO.

  1. 1
    XIAO ESP32-S3seeedstudio.com ↗
    21 × 17.8 mm, Wi-Fi and Bluetooth. Its USB-C port is how you install the firmware the first time.
  2. 2
    2.4 GHz antenna
    Comes with the XIAO. Plug it in: without it the screen says “No Wi-Fi”.
  3. 3
    Round Display for XIAOseeedstudio.com ↗
    1.28″ round touch screen, 240 × 240, on a 39 mm board. The XIAO plugs into the sockets on its back.
  4. →
    Put it togetherBuild guide →
    What to buy and how the three parts plug together, no soldering.
  5. →
    Try it
    Tap, double tap, drag the ring or swipe, right on the screen.
Round · exploded viewmm

Scroll to put it together

Round · 3 parts
  1. 1
    seeedstudio.com ↗
    21 × 17.8 mm, Wi-Fi and Bluetooth. Its USB-C port is how you install the firmware the first time.
  2. 2
    Comes with the XIAO. Plug it in: without it the screen says “No Wi-Fi”.
  3. 3
    seeedstudio.com ↗
    1.28″ round touch screen, 240 × 240, on a 39 mm board. The XIAO plugs into the sockets on its back.
Simple · 1 part
  1. 1
    XIAO ESP32-C6seeedstudio.com ↗
    21 × 17.5 mm. Up to seven wall switches or push buttons: D0 to D5, plus the BOOT button on the board.
  2. 2
    The switches already in your wallBuild guide →
    Toggle switches or push buttons, plus a few wires. The build guide shows what to buy and how to wire them.
Simple · try it→ Hallway · Tropics · 92%
Simplemm

Runs on your home network

Presses go from the switch to your Hue Bridge. The console only stores settings; switches keep working if it is down.

Wi-Fi stays on the switch

Your Wi-Fi password goes from the browser to the switch over USB and never reaches the console.

Free, no tracking

No ads and no analytics. Sponsorship does not unlock anything.

Open source

The console is AGPL-3.0 and the firmware is MIT. Read it, fork it, host your own ↗

What you need

  • 01 · Bridge

    A Philips Hue Bridge or Hue Bridge Pro

    Plugged into your router. The switch talks to it over your home network, so bulbs paired only by Bluetooth won't work.

  • 02 · Lights

    Hue lights, set up in the Hue app

    Rooms, zones and scenes come from the Bridge. Make them in the Hue app first; the switch picks them up when it pairs.

  • 03 · Board

    A switch on 2.4 GHz Wi-Fi

    A XIAO ESP32-C6 for Simple, or the Round Display with a XIAO ESP32-S3. It joins your 2.4 GHz network, the one the Bridge is on.

From USB to wall in three steps

Full setup guide →
  1. USB-CChrome · EdgeWeb Serial
    01

    Install over USB, once

    Plug the board into your computer and open Setup in Chrome or Edge. It installs the firmware and saves your Wi-Fi. Nothing to compile, and later updates come over Wi-Fi.

  2. 02

    Pair with your Bridge

    Press the button on your Hue Bridge when the switch asks. It sends the console your rooms, zones, lights and scenes.

  3. Page 1 · Living
    tapon / off
    double tapSunset, Aurora
    ringdim
    03

    Choose what it does

    Pick the room, the scenes and what a tap, double tap or hold does. The switch picks up your changes on its own.

Sign-up is by invitation for now.

Join the waitlist and you get an email when your account is ready. The setup guide is open to everyone.

Philips Hue is a trademark of Signify. This project is independent and is not affiliated with, endorsed by or sponsored by Signify. XIAO is a trademark of Seeed Studio.